Ball Bearing Components – METRIC


Table of Contents

PAGE NUMBER

Introduction

1

Operating Conditions

1

Ball Bearing Components
Rotainers® 2
Retainers 3
Demountable Steel Guide Post Bushings 4
Press Fit Steel Sleeve Bushings 6
Straight Guide Posts 7
Flanged Demountable Guide Posts 8

Ball Bearing Engineering Data
Boring Procedures and Dimensions 10
Installation and Assembly Instructions 11

The Industry Standard, Conformed to Your Needs

LEMPCO customization services will go to virtually any length to satisfy your needs. Now, the
full range of answers to your requirements is at your command. It could be a simple modification
or something quite exotic. Whatever your need, LEMPCO will work closely with you to make
sure your specs are met.

The pride we have in our ability to perform (and to provide you with profitable production
performance) is stamped on every part we make. The LEMPCO stamp means satisfaction in
terms of quality, dependability and service since 1918. Other brands may appear the same; for
a system to truly perform, look for the LEMPCO name.

We pledge that all of our products – innovative or conventional – will be manufactured to the
same high quality level throughout the coming years.


INTRODUCTION


BALL BEARING
ASSEMBLY
LUBRICATION
RECOMMENDATION
IN THE OPERATION OF
THE BALL ASSEMBLY,
ADD LUBRICANT ONCE
EACH 8-HOUR SHIFT
BY SPRAY OR BRUSH
APPLICATION.
USE A LIGHTWEIGHT
SPINDLE OIL OR
AUTOMOTIVE TYPE
AUTOMATIC
TRANSMISSION FLUID.
CAUTION: NEVER
USE GREASE!

OPERATING CONDITIONS


TYPE 1 TYPE 2 TYPE 3


LEMPCO customization services will go to virtually any length to
satisfy your guidance system needs – any diameter; any material,
hardness, or finish; in any component or configuration – anything!

You have a process or problem that standard guidance system
solutions can’t handle. That’s where LEMPCO guidance systems
come in.

Punch Shoe

Small Radius
Guide Post
Set Screw
ROTAINER®

Bushing

Blue stripe

trademark

of Lempco

Large Radius Die Shoe

PRELOADED

MAXIMUM
NUMBER OF
BALL BEARINGS
IN CONTACT WITH
THE GUIDE POST
AND THE BUSHING


PRELOAD
RELIEVED


THE GUIDE PIN
(ONLY) LEAVES
THE BUSHING
WHILE THE BALL
CAGE REMAINS
IN THE BUSHING

FULL
DISENGAGEMENT


BOTH THE GUIDE
PIN AND THE BALL
CAGE LEAVE THE
BUSHING


1



ROTAINERS®


For Ball Bearing Applications



Nom. Post
Diameter
A
Length(mm)
L
CatalogNumber
19
39 367-19390
51 367-19510
65 367-19650
25
39 367-25390
51 367-25510
65 367-25650
32
62 367-32580
75 367-32700
87 367-32830
40
68 367-40650
81 367-40770
100 367-40960
44
75 367-44700
87 367-44830
113 367-44108
50
89 367-50830
108 367-50102
121 367-50114
63 178 367-63178
80 178 367-80178


Diameters and lengths not listed are available
by special order.
Designed to rotate on the post, as well as maintain its

The LAST length for each diameter shown in
the table should be used for general die set

vertical motion, LEMPCO’s ROTAINER® was developed to

applications. Other lengths are for limited

greatly reduce the amount of tracking. The disengagement space and special applications.

of the guide post from the bushing by 6.35mm at the top of

the stroke will allow the ROTAINER® to rotate 360° on the

guide post. The ROTAINER®, while still designed to track,

(assuring a measurable amount of preload) will enable

stampers to achieve high press production by reducing

expensive replacement costs.

Rotainer® Slide ReplacementWith Screw Assembly Number
of
InsertsNom.
(mm)
AssemblyPart No.
19 899-9406 1
25 899-9408 1
32 899-9410 1
40 899-9412 1
44 899-9414 1
50 899-9416 2
63 899-9420 2
80 899-9424 2

NOTE: Under a preloaded condition,
the ROTAINER® will only move
vertically.

2


PRECISION
BALL BEARING RETAINERS

For Ball Bearing Applications


Nom. Post
Diameter (mm)
A
Length(mm)
L
CatalogNumber
19
39 937-19390
51 937-19510
65 937-19650
25
39 937-25390
51 937-25510
65 937-25650
32
58 937-32580
70 937-32700
83 937-32830
40
65 937-40650
77 937-40770
96 937-40960
44
70 937-44700
83 937-44830
108 937-44108
50
83 937-50830
102 937-50102
114 937-50114
63 178 937-63178
80 178 937-80178



The LAST length for each diameter shown in
the table should be used for general die set
applications. Other lengths are for limited The LEMPCO Precision Ball Bearing Retainer possessesspace and special applications.

resistance to normal wear and to lateral motion, is smooth in
high speed operation and offers precise die register. It is keyed
to the guide post slot with a set screw.

3



DEMOUNTABLE STEEL
GUIDE POST BUSHINGS


For Ball Bearing Applications



LEMPCO Demountable Guide Post
Bushings are manufactured from 52100
tool steel and precision machined. See
pages 10–11 for mounting instructions.

Diameters and lengths not listed are
available by special order.

NOTE:
The 966 Series product line is
not stocked, but is available as
a special order.

Nom.
Post
Diameter
B C E F Radius L CatalogNumbersM N
25 43.956 51 30
25
31 40.555 966-25055
30 60 966-25060
35 65 966-25065
40 70 966-25070
45 75 966-25075
50 80 966-25080
55 85 966-25085
60 90 966-25090
65 95 966-25095
32 53.959 61 30
35
36.627 47.34665 966-32065
40 70 966-32070
45 75 966-32075
50 80 966-32080
55 85 966-32085
60 90 966-32090
65 95 966-32095
75 105 966-32105
80 110 966-32110
85 115 966-32115
100 130 966-32130
110 140 966-32140
125 155 966-32155
40 64.960 72 35
40
42.190 52.908
75 966-40075
45 80 966-40080
50 85 966-40085
55 90 966-40090
60 95 966-40095
65 100 966-40100
75 110 966-40110
80 115 966-40115
85 120 966-40120
90 125 966-40125
100 135 966-40135
105 140 966-40140
120 155 966-40155

4



DEMOUNTABLE STEEL
GUIDE POST BUSHINGS


For Ball Bearing Applications


19.05mm40 75 966-44075
55 90 966-44090
60 95 966-44095
65 100 966-44100
75 110 966-44110
80 115 966-44115
90 125 966-44125
100 135 966-44135
105 140 966-44140
120 155 966-44155
130 165 966-44165
145 180 966-44180
155 190 966-44190
40 75 966-50075
55 90 966-50090
60 95 966-50095
65 100 966-50100
75 110 966-50110
80 115 966-50115
90 125 966-50125
100 135 966-50135
105 140 966-50140
120 155 966-50155
130 165 966-50165
145 180 966-50180
155 190 966-50190
90 125 966-63125
105 140 966-63140
120 155 966-63155
130 165 966-63165
145 180 966-63180
155 190 966-63190
90 125 966-80125
105 140 966-80140
120 155 966-80155
130 165 966-80165
145 180 966-80180
155 190 966-80190
44 73.959 81 35 46.939 57.658
50 80.959 91 35 51.714 62.408
63 94.960 105 35 58.852 69.571
80 111.960 122 35 67.590 78.283
M N
Nom.
Post
Diameter
B C E F CatalogNumbersL Radius
NOTE:
The 966 Series product line is
not stocked, but is available as
a special order.

5



PRESS FIT STEEL
SLEEVE BUSHINGS



For Ball Bearing Applications
LEMPCO’s Press Fit Steel Sleeve Bushings are
manufactured from 52100 tool steel and precision
machined. The I.D. is ground and honed to a superfine
finish to minimize resistance to free action of the
retainer/Rotainer® bearings.

See pages 10–11 of this catalog for mounting
instructions.

Nom.
Post
Diameter
B L CatalogNumbers
19 36.000
50 967-19500
55 967-19550
65 967-19650
70 967-19700
75 967-19750
80 967-19800
90 967-19900
95 967-19950
100 967-19100
110 967-19110
125 967-19125
150 967-19150
25 44.000
75 967-25750
80 967-25800
90 967-25900
95 967-25950
100 967-25100
105 967-25105
115 967-25115
120 967-25120
125 967-25125
140 967-25140
150 967-25150
165 967-25165
175 967-25175
32 54.000
75 967-32750
80 967-32800
90 967-32900
95 967-32950
100 967-32100
105 967-32105
115 967-32115
125 967-32125
140 967-32140
150 967-32150
165 967-32165
175 967-32175
200 967-32200
230 967-32230

Nom.
Post
Diameter
B L CatalogNumbers
40 65.000
100 967-40100
105 967-40105
115 967-40115
120 967-40120
125 967-40125
135 967-40135
140 967-40140
150 967-40150
165 967-40165
175 967-40175
190 967-40190
200 967-40200
215 967-40215
230 967-40230
250 967-40250
280 967-40280
300 967-40300
44 74.000
125 967-44125
135 967-44135
140 967-44140
150 967-44150
165 967-44165
175 967-44175
190 967-44190
200 967-44200
215 967-44215
230 967-44230
250 967-44250
280 967-44280
300 967-44300
330 967-44330
50 81.000
125 967-50125
135 967-50135
140 967-50140
150 967-50150
165 967-50165
175 967-50175
190 967-50190

Nom.
Post
Diameter
B L CatalogNumbers
50 81.000
200 967-50200
215 967-50215
230 967-50230
250 967-50250
280 967-50280
300 967-50300
330 967-50330
350 967-50350
63 95.000
150 967-63150
165 967-63165
175 967-63175
190 967-63190
200 967-63200
215 967-63215
230 967-63230
250 967-63250
280 967-63280
300 967-63300
330 967-63330
350 967-63350
80 112.000
150 967-80150
165 967-80165
175 967-80175
190 967-80190
200 967-80200
215 967-80215
230 967-80230
250 967-80250
280 967-80280
300 967-80300
330 967-80330
350 967-80350

6



STRAIGHT
GUIDE POSTS


For Ball Bearing Applications


LEMPCO’s Straight Guide Posts for ball bearing assemblies are manufactured
from 52100 tool steel and precision ground.

See pages 10–11 for mounting instructions.

Post
Diameter
A
Length
L
CatalogNumbers
19
75 957-19750
90 957-19900
100 957-19100
110 957-19110
115 957-19115
120 957-19120
125 957-19125
150 957-19150
25
100 957-25100
110 957-25110
115 957-25115
120 957-25120
125 957-25125
135 957-25135
140 957-25140
145 957-25145
150 957-25150
165 957-25165
175 957-25175
190 957-25190
200 957-25200
215 957-25215
230 957-25230
32
125 957-32125
135 957-32135
140 957-32140
145 957-32145
150 957-32150
165 957-32165
175 957-32175
190 957-32190
200 957-32200
215 957-32215
230 957-32230
250 957-32250
260 957-32260
280 957-32280
300 957-32300

Post
Diameter
A
Length
L
CatalogNumbers
40
125 957-40125
135 957-40135
140 957-40140
145 957-40145
150 957-40150
165 957-40165
175 957-40175
190 957-40190
200 957-40200
215 957-40215
230 957-40230
240 957-40240
250 957-40250
265 957-40265
280 957-40280
290 957-40290
300 957-40300
315 957-40315
330 957-40330
360 957-40360
44
125 957-44125
135 957-44135
140 957-44140
145 957-44145
150 957-44150
165 957-44165
175 957-44175
190 957-44190
200 957-44200
215 957-44215
230 957-44230
240 957-44240
250 957-44250
265 957-44265
280 957-44280
290 957-44290
300 957-44300
315 957-44315
330 957-44330
360 957-44360

Post
Diameter
A
Length
L
CatalogNumbers
50
150 957-50150
165 957-50165
175 957-50175
190 957-50190
200 957-50200
215 957-50215
230 957-50230
240 957-50240
250 957-50250
265 957-50265
280 957-50280
290 957-50290
300 957-50300
315 957-50315
330 957-50330
360 957-50360
380 957-50380
400 957-50400
430 957-50430
460 957-50460
63
200 957-63200
215 957-63215
230 957-63230
240 957-63240
250 957-63250
265 957-63265
280 957-63280
300 957-63300
315 957-63315
330 957-63330
360 957-63360
380 957-63380
430 957-63430
500 957-63500
80
200 957-80200
215 957-80215
230 957-80230
250 957-80250
280 957-80280
300 957-80300
330 957-80330
360 957-80360
430 957-80430
500 957-80500


7



FLANGED DEMOUNTABLE
GUIDE POSTS


For Ball Bearing
Applications


The LEMPCO Flanged
Demountable Guide Post
for ball bearing assemblies
is designed for those who
prefer the convenience of
a removable post to expedite
die repairs. The post is tap
fitted into the pin plate bore
with the flange flush to the
ground surface. See pages
10–11 for bore size data.

These Demountable Guide
Posts are manufactured from
52100 tool steel.

Nominal Length
A
Flange
B C E F L
CatalogNumbers
24.953
24.940
33 24.953
24.940
30
60 90 958-25090
70 100 958-25100
80 110 958-25110
85 115 958-25115
90 120 958-25120
95 125 958.25125
105 135 958-25135
110 140 958-25140
115 145 958-25145
120 150 958-25150
135 165 958-25165
145 175 958-25175
160 190 958-25190
170 200 958-25200
185 215 958-25215
200 230 958-25230
31.953
31.940
40 31.953
31.940
30
85 115 958-32115
90 120 958-32120
95 125 958-32125
105 135 958-32135
110 140 958-32140
115 145 958-32145
120 150 958-32150
135 165 958-32165
145 175 958-32175
160 190 958-32190
170 200 958-32200
185 215 958-32215
200 230 958-32230
220 250 958-32250
250 280 958-32280
270 300 958-32300
39.952
39.939
48 39.952
39.939
36
79 115 958-40115
84 120 958-40120
89 125 958-40125
99 135 958-40135
104 140 958-40140
109 145 958-40145
114 150 958-40150
129 165 958-40165
139 175 958-40175
154 190 958-40190
164 200 958-40200
179 215 958-40215
194 230 958-40230
204 240 958-40240
214 250 958-40250
224 260 958-40260
244 280 958-40280
254 290 958-40290
264 300 958-40300
279 315 958-40315
294 330 958-40330
324 360 958-40360
43.952
43.939
57 43.952
43.939
43
82 125 958-44125
92 135 958-44135
97 140 958-44140
102 145 958-44145
107 150 958-44150
112 155 958-44155
122 165 958-44165

8



FLANGED DEMOUNTABLE
GUIDE POSTS


For Ball Bearing


Diameter Nominal Length
CatalogNumbers
Post
A
Flange
B C E F L
43.952
43.939
57 43.952
43.939
43
132 175 958-44175
147 190 958-44190
157 200 958-44200
172 215 958-44215
187 230 958-44230
197 240 958-44240
207 250 958-44250
217 260 958-44260
237 280 958-44280
247 290 958-44290
257 300 958-44300
272 315 958-44315
287 330 958-44330
317 360 958-44360
337 380 958-44380
387 430 958-44430
49.952
49.939
63 49.952
49.939
49
91 140 958-50140
96 145 958-50145
101 150 958-50150
106 155 958-50155
116 165 958-50165
121 170 958-50170
126 175 958-50175
131 180 958-50180
141 190 958-50190
146 195 958-50195
151 200 958-50200
166 215 958-50215
181 230 958-50230
191 240 958-50240
201 250 958-50250
211 260 958-50260
231 280 958-50280
241 290 958-50290
251 300 958-50300
266 315 958-50315
281 330 958-50330
311 360 958-50360
331 380 958-50380
351 400 958-50400
381 430 958-50430
411 460 958-50460
62.952
62.939
76 62.952
62.939
49
151 200 958-63200
166 215 958-63215
181 230 958-63230
201 250 958-63250
231 280 958-63280
251 300 958-63300
281 330 958-63330
311 360 958-63360
381 430 958-63430
451 500 958-63500
79.952
79.939
93 79.952
79.939
62
138 200 958-80200
153 215 958-80215
168 230 958-80230
188 250 958-80250
218 280 958-80280
238 300 958-80300
268 330 958-80330
298 360 958-80360
368 430 958-80430
438 500 958-80500


9



BALL BEARING
ENGINEERING DATA


Boring Procedures and Dimensions


Holes for LEMPCO Ball Bearing Guide Posts
and Bushings should be jig bored for best results.
The punch holder and dieholder should be clamped
together and bored in one setup in order to maintain
dead center alignment between the upper and lower
bores. If it is not possible to bore in this manner, a
tolerance of ±.0127mm between centers (see
illustration) must be held. Bores should be smooth
and free from tool marks to provide proper bearing
area for the guide post and bushing.

Dieholder bores must be perpendicular to that
surface of the dieholder which will back up the die.
The bottom surface of the dieholder must be parallel
to the die backup surface. The same holds true for
the punch holder: the bores must be perpendicular
to that surface which will back up the punches, and
the top surface parallel to the punch backup surface.

Break the corners of the bored holes to a generous
chamfer. On sets with a symmetrical profile one pin
and bushing should be offset to prevent accidental
reversing of the punch holder during assembly.

All LEMPCO Ball Bearing Guide Posts, Bushings
Retainers and Rotainers are completely interchangeable
without any necessity whatsoever for
select fitting of any kind, and if mounted in accordance
with boring and assembly instructions given on this
and the following page do not require any grinding,
honing, lapping, or any other modifications of any
kind. Please note the dimensions given in the
following table. Our experience over many years
proves that these are optimum dimensions. Variations
must be avoided.


BORE CHART BALL BEARING COMPONENTS (METRIC)


Nominal
Guide
Post
Diameter
#957-SERIES
STRAIGHT
GUIDE PIN
(PRESS FIT)
#958-SERIES
DEMOUNTABLE
GUIDE PIN
(TAP FIT)
#967-SERIES
STRAIGHT
SLEEVE
BUSHING
(PRESS FIT)
#966-SERIES
DEMOUNTABLE
SHOULDER
BUSHING
(TAP FIT)
BORE SIZE BORE SIZE BORE SIZE BORE SIZE
19mm 18.9683 +.000
–.025 N/A 35.9685 N/A +.0000
–.0127
25mm 24.9705 +.000
–.025 24.9633 +.0000
–.0127 43.9695 +.0000
–.0127 43.9695 +.0000
–.0127
32mm 31.9708 +.000
–.025 31.9632 +.0000
–.0127 53.9703 +.0000
–.0127 53.9703 +.0000
–.0127
40mm 39.9692 +.000
–.025 39.9616 +.0000
–.0127 64.9709 +.0000
–.0127 64.9709 +.0000
–.0127
44mm 43.9695 +.000
–.025 43.9623 +.0000
–.0127 73.9701 +.0000
–.0127 73.9701 +.0000
–.0127
50mm 49.9696 +.000
–.025 49.9620 +.0000
–.0127 80.9703 +.0000
–.0127 80.9703 +.0000
–.0127
63mm 62.9695 +.000
–.025 62.9613 +.0000
–.0127 94.9710 +.0000
–.0127 94.9710 +.0000
–.0127
80mm 79.9692 +.000
–.025 79.9615 +.0000
–.0127 111.9706 +.0000
–.0127 111.9706 +.0000
–.0127

(UNLESS OTHERWISE NOTED, ALL DIMENSIONS ARE IN MILLIMETERS)

10


BALL BEARING
ENGINEERING DATA

Installation and Assembly Instructions


In order to maintain the die and
punch alignment, it is essential that
the guide posts and bushings be
at absolute right angles with the
punch and die backup surfaces.

FIGURE 1 represents a typical
guide post and ROTAINER®. Please
note that the end of the guide post
with the small radius is press fit
into the punch shoe, and that the
ROTAINER® is assembled with the
ROTAINER® slide assembly toward
the same end of the guide post. On
the bushing, however, the end with
the large outside diameter radius
is press fit into the die shoe.

NOTE: LEMPCO Demountable Bushings
and Flanged Demountable Guide Posts are
tap fitted. Bores should be to specifications,
and both bushings and guide posts should
be seated flush to ground surface of support
shoe and held securely by clamps and cap
screws. These bushings and guide posts
are removable; on installation the die will
register accurately.

Check the squareness of the
guide post or bushing with a
precision square. Tap the sides
slightly with a soft hammer until
the guide post or bushing is
perpendicular.

Press fit about 6.35mm and
check with the precision square
again, tapping the sides with a soft
hammer as necessary, to ensure
squareness. A bronze, babbitt or
fiber hammer is recommended.

NOTE: With Demountable Boss Bushings,
be sure to press against the hardened liner
and not against the casting.

Press fit by small increments
(not over 12.70mm each) checking
with the precision square after
each press. Do not allow guide
post or bushing to protrude through
the lower side of the plate. It is
advisable to place a.3968mm shim
under the guide post or bushing as
a stop.

For Demountable Boss Bushings
and Demountable Bushings, after
the bushing is tap fit to the shoulder,
the shoe may be drilled with the
bushing in place. Tighten screws
gradually, moving from one to
another until all are tight.

After complete assembly of the
bushings, check the ID top and
bottom for taper. Should taper be
found, hone the ID until original
size is obtained.

Note: This should not be necessary if
boring instructions were strictly adhered to.

Assemble ROTAINER® to guide
post (FIGURE 1) by screwing the
set screw in until flush with special
ROTAINER® slide. Vertical and
rotational movement should now be
tested to insure freedom of movement.
After testing is completed,
stake set screw. Lubricate only
with a light spindle oil.

Note: The only tool necessary to assemble
the ROTAINER® is a screw driver.

Assemble punch and die holder.
Be sure to allow ROTAINERS® to
hang free (see FIGURE 2) supported
by the special ROTAINER® slide
when assembling die set. Work the
punch holder up and down a few
times to assure there is no binding.

Punch
Shoe
Small
Radius

Guide
Post

ROTAINER®
Bushing

Large Radius Die Shoe

FIGURE 1

FIGURE 2
Right Way Wrong Way Wrong Way
11



NOTES


12



Ball Bearing Components – METRIC



The LEMPCO Value Proposition


LEMPCO is a recognized leader in providing quality ball bearing components:
1.
Rotainer® designed ball cage that minimizes tracking.
2.
Precision Rotainer® and retainer that provides accuracy and repeatability
in high speed applications.
3.
Quality pins and bushings are made from 52100 tool steel and are precision ground.

LEMPCO offers high quality die sets with either ball bearing or plain bearing components.
Pins and bushings are manufactured using high quality steel and are precision ground.

LEMPCO has a strong distribution network with over 250 distributors located around the
world to service our valued customers.

LEMPCO’s manufacturing capabilities allow larger size die sets to be offered (240 in. by
120 in.) and complex machining to be available with exceptional deliveries.
QUALITY .. DEPENDABILITY .. SERVICE
SINCE 1918
THE GLOBAL STANDARD WITH DISTRIBUTORS WORLDWIDE


Quality, precision and dependability
are the requirements of today’s production processes–
from ultra-high-speed stamping technology
to computer-driven CNC manufacturing.


LEMPCO designs its components in order to provide you with precision and
cost-effective performance... run after run. We have the proven experience
in the selection of metals, developing designs and understanding the details
of your needs.


LEMPCO KNOWS WHAT IT TAKES TO KEEP YOUR DIES RUNNING
AND WE KNOW HOW TO DELIVER IT.



Ball BearingComponents– METRIC –
© 2006 LEMPCO. All rights reserved. L-1008-1 09/06
Distributed by:
The Anchor Danly Company
6779 Engle Road Suite A-F
Cleveland, OH 44130-7926
VISIT OUR WEBSITE AT: www.lempco.com
E-MAIL US AT: This e-mail address is being protected from spambots. You need JavaScript enabled to view it
OR: This e-mail address is being protected from spambots. You need JavaScript enabled to view it
WITHIN THE USA & CANADA
CALL: 800-321-8632
FAX: 800-221-6310
OUTSIDE THE USA & CANADA
CALL: 001-248-489-7816
FAX: 001-248-553-6842
Ball BearingComponents– METRIC –
© 2006 LEMPCO. All rights reserved. L-1008-1 09/06
Distributed by:
The Anchor Danly Company
6779 Engle Road Suite A-F
Cleveland, OH 44130-7926
VISIT OUR WEBSITE AT: www.lempco.com
E-MAIL US AT: This e-mail address is being protected from spambots. You need JavaScript enabled to view it
OR: This e-mail address is being protected from spambots. You need JavaScript enabled to view it
WITHIN THE USA & CANADA
CALL: 800-321-8632
FAX: 800-221-6310
OUTSIDE THE USA & CANADA
CALL: 001-248-489-7816
FAX: 001-248-553-6842
 

Worldwide Presence

England, Germany Thailand

 

England, Germany and Thailand

Please click on country name nearest to you to see our contact details or to enquire about our products and services.

Agent for Universal Die & Stampings

          
Universal Die & Stampings